RCU Forums
0 2018/04/18 06:40:43
0 2018/04/18 06:40:48
0 2018/04/18 06:40:53
some rivets on the control surfaces
some rivets on the control surfaces
0 2018/04/19 14:18:48
Vladimir machined some new fittings for the new tank plug.
Vladimir machined some new fittings for the new tank plug.
0 2018/04/19 14:18:55
some panel lines and rivets
some panel lines and rivets
0 2018/05/06 17:05:20
white bottom and white trim you
white bottom and white trim you
0 2018/05/06 17:05:41
rudder with panel lines and rivets and chart tape where rudder hinges over
rudder with panel lines and rivets and chart tape where rudder hinges over
0 2018/05/06 17:05:49
tape off for the gray top
tape off for the gray top
0 2018/05/06 17:05:55
gray sprayed
gray sprayed
0 2018/05/06 17:05:59
tape removed
tape removed
0 2018/05/06 17:06:02
elevons and rudder done
elevons and rudder done
0 2018/05/06 17:06:05
the flaps are also painted
the flaps are also painted
0 2018/05/06 19:02:55
0 2018/05/20 20:49:00
0 2018/05/20 20:49:48
Mid 50s for a temp today and a chance of rain but I squeezed in priming the hatches and fuse.shot them outside then brought them inside to dry........ I put nick i the pic because he keeps telling me he is almost as tall as me.
Mid 50s for a temp today and a chance of rain but I squeezed in priming the hatches and fuse.shot them outside then brought them inside to dry........ I put nick i the pic because he keeps telling me he is almost as tall as me.
0 2018/05/20 20:49:51
I put a few rivets and panels in the primer on the hatches
I put a few rivets and panels in the primer on the hatches
0 2018/05/23 21:26:42
I made some templates to scratch some panels into the primer
I made some templates to scratch some panels into the primer
0 2018/05/23 21:26:45
this was the best way to draw the line where the white and gray paint meet
this was the best way to draw the line where the white and gray paint meet
0 2018/05/28 19:58:51
some rivets and panel lines on the top front of the fuse
some rivets and panel lines on the top front of the fuse
0 2018/05/28 19:58:54
some rivets and panel lines on the top rear of the fuse. they will all need to be subdued with some steel wool of light sanding
some rivets and panel lines on the top rear of the fuse. they will all need to be subdued with some steel wool of light sanding
0 2018/05/28 19:58:56
0 2018/07/24 18:36:26
0 2018/07/24 18:36:32
0 2018/07/24 18:36:35
0 2018/07/24 18:36:51
0 2018/07/24 18:36:57
0 2018/07/31 17:32:12
0 2018/07/31 17:32:21
the servos for the elevons and rudder went in
the servos for the elevons and rudder went in
0 2018/08/12 18:19:53
some of the nice linkages Vladimir machined for the plane
some of the nice linkages Vladimir machined for the plane
0 2018/08/12 18:19:58
I had center marked in the primer then I painted over it. I had to remind it.
I had center marked in the primer then I painted over it. I had to remind it.
0 2018/08/12 18:20:02
The arm for the rudder servo wit some temp. linkage
The arm for the rudder servo wit some temp. linkage
0 2018/08/12 18:20:05
dremmeled open some slots for the linkage
dremmeled open some slots for the linkage
0 2018/08/12 18:28:42
A few tabs of hobby foil to keep primer out of the threads
A few tabs of hobby foil to keep primer out of the threads
0 2018/08/12 18:28:48
some bottom primer on the wings
some bottom primer on the wings
0 2018/08/12 18:29:21
some primer on the tops of the wings. the sticks are holding things open so the primer doesn't glue anything shut
some primer on the tops of the wings. the sticks are holding things open so the primer doesn't glue anything shut
0 2018/08/12 18:29:24
Some G 10 for the ears on the rudder servo hatch
Some G 10 for the ears on the rudder servo hatch
0 2018/08/14 20:19:16
And a nice countersunk screw down to the g 10
And a nice countersunk screw down to the g 10
0 2018/08/14 20:19:19
I precisely marked where the clevice pin holes needed to be drilled
I precisely marked where the clevice pin holes needed to be drilled
0 2018/08/14 20:19:34
and then precisely drilled on the wrong side of the line
and then precisely drilled on the wrong side of the line
0 2018/08/14 20:19:43
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.